How to turn on a gas burner. How to connect a gas stove in an apartment yourself. Installation of a gas stove. Organizing a place for a gas stove

Autonomous heating systems are experiencing a rebirth today. This is due to the fact that the country recently began a boom in individual construction. It is quite difficult to connect a country house to central communications. If this is done, then the coziness and comfort in such a home will depend on a number of unreliable factors, including the condition of the pipes, the operation of the boiler room, etc. This can also include centralized energy transmission.

If you also decide to follow the experience of the majority and choose a gas boiler for heating a country house, then it is certainly recommended that you familiarize yourself with the operating recommendations, from which you can also learn how a gas boiler works, how to turn on this equipment, and also how to avoid its premature shutdown. breakdowns. For example, in order to prevent foreign bodies from entering the system, a hard cleaning filter should be installed at the inlets of running water, gas, and the heating circuit. It is also important to ensure that the system contains a voltage stabilizer, which is located at the input of the system. This will protect the control board from voltage surges in the network.

If you are wondering how to turn on a Baxi brand floor-standing gas boiler, you need to follow a certain technology. In the first step, you must open the gas valve, usually it is located under the equipment itself. It is important to make sure that the system has the required pressure, only then can power be supplied to the device. Then you should press the “Start” button and set the device to “Winter” or “Summer” mode.

The panel has special buttons with which you can set the desired temperature values in the boiler and hot water supply circuits. This will allow the main burner to turn on. If you purchased a gas boiler, you need to ask how to turn it on before unpacking the product. After you have completed all the above steps, you need to make sure that the boiler is working, this will be indicated by a special burning flame symbol on the display.

Connection nuances

After you have figured out how to turn on the heating gas boiler, you can set it to the “Summer” mode, and the device will work, producing only hot domestic water. When starting is completed, plugs may form inside the fuel supply pipe. In this case, the burner will not turn on and the boiler will be blocked. In this situation, it is necessary to repeat the steps mentioned above again. Ultimately, you must ensure that gas begins to flow into the burner. Then the "R" button is pressed and held for approximately 2 seconds.

A gas stove, like other household appliances, should be handled in accordance with basic safety rules. If you purchased a new stove or never turned on the existing one, you need to act carefully and follow a certain order of steps.

Locate the valve on the gas pipe and open it completely. This will ensure the supply of natural gas to your stove. Consider the symbols near the burners: they show the correspondence of the burners and the relays being turned. Select one burner to turn on. Light a match, bring it to the divider, turn the desired relay counterclockwise a quarter turn. Adjust the flame to the appropriate size. Make sure the light is blue. If the flame is orange, turn off the burner and clean it, or call a professional to do this procedure. A stove with an electric ignition function turns on differently. The semi-automatic system works like this: you press the ignition button (usually located in the same row as the burners, slightly to the left), and a spark is sent to all burners. All that remains is to turn the selected relay. On a stove with automatic ignition, you need to press the relay a little and then turn it to the left.

To turn on the oven, open the door and look at the very bottom for one or two holes that lead to the burner. Turn the relay, then hold a lit match to each hole (it's easier to use fireplace matches or long toothpicks). The flame should ignite and spread across the entire surface of the burner. If this is exactly what happened, close the door and wait for the oven to heat up to the required temperature. Operating a stove with electric ignition is much simpler: we turn on the oven in the same way as external burners.

Answers to most questions about using a gas stove can be found in the factory instructions. If you are unable to turn on the stove yourself and cannot find a way to fix the problem, call a gas service worker to check the entire system.

Gas water heaters are a very popular type of water heater. Having selected a suitable model and installed it in an apartment or house, all that remains is to learn how to turn on the speaker. Among the mandatory manipulations is the opening of the gas tap that supplies gas to the device, as well as the opening of the water tap through which cold water will flow into the device. In this case, your actions will depend on the type of ignition used in your column model.

How to light using ignition type?

Manual ignition

This method is already outdated and is used extremely rarely in modern speakers. Such devices are poorly protected both from changes in water pressure and from fire extinguishing. It is currently not recommended to install such devices at home.

How to light a column with manual ignition:

Unscrew the valve on the tap that supplies water to the column.
Light the wick using a match or lighter.
Open the valve on the tap supplying gas to the column.
Sometimes, in order to ignite the burner, you need to wait a little until the air comes out of its channel. To speed up the process, first open and then close the hot water tap several times.

Piezo ignition

This option of igniting the column is more modern and widespread. It is very simple to use, but it has the disadvantage of increased gas consumption. While the column is not working, the wick is still smoldering inside it, so the gas, although in small quantities, is constantly burned.

How to light a column with piezo ignition:

To start, you need to press a button that acts on the piezoelectric element. This will provide a spark to ignite the pilot wick.
Open the tap supplying gas to the device.

The following video demonstrates this clearly.

Automatic ignition

This is the most modern and profitable option for igniting geysers. It is also called electric because it is based on the transmission of an electric spark. Its appearance is provided either by batteries or a hydraulic turbine. The combustion will be controlled by different sensors, and as soon as the user turns off the hot water tap, the ignition wick will go out.

How to light a column with electric ignition:

Make sure that gas and cold water are supplied to the column.
Open the hot water tap.

Watch a short video review.

Housewives who have used electric stoves and ovens for years, when faced with gas kitchen equipment, are lost and do not know how to light the oven in a gas stove. In fact, there is nothing complicated about it. Those who use gas stoves light the oven quickly and without hesitation. Well, beginners will have to master the oven in order to light the oven correctly.

How to light an oven in a gas stove?

Ways to turn on the oven

A gas stove in the kitchen is much more convenient than an electric one. In the event of an unexpected power outage, you can safely cook food or bake something in the oven, which will be absolutely impossible in the case of an electric stove. However, an inexperienced user may encounter difficulties when lighting the oven. Therefore, before turning on the oven, it is better to study the operating instructions.

Currently, stores sell standard stoves with two types of ignition:

Automatic;

In the case of automatic ignition, everything is simple. For gas to start flowing into the burner, turn the tap on the stove panel, which is responsible for heating the oven, and set it to the desired temperature. Now press the auto-ignition button and hold it for 15-20 seconds. The gas in the oven should light up. If this does not happen, stop feeding by releasing the button and repeat all over again.

If the stove does not turn on, call a specialist and ask why it is not working and how to turn on the gas oven. If you have manual ignition, the first time you turn on the oven you will have to tinker and get used to it. Find a small hole in the bottom wall of the stove through which gas flows from the burner. Light a match and bring it to this hole while turning on the oven tap. A working oven should light up immediately.

Safety rules when handling a gas oven

Of course, in order to understand the principles of operation of a gas stove and protect yourself from troubles, it is better to read about the safety rules and operation of the device before you start using the equipment. Some tips may help, for example:

Before turning on the stove, check the hose connections;

Before lighting a gas oven, you need to keep it open for a while to prevent gas from accumulating inside;

Always keep an eye on the oven flame;

Wipe and wash the oven from time to time, because in a dirty stove, gas combustion does not occur completely;

Do not keep the oven open for a long time and do not heat the room with it.

Any problems with a gas stove are a reason to contact a specialist. Don't forget about this to protect yourself and your loved ones from unwanted consequences.

Do you want to install individual heating in your home? Have you already installed and connected gas equipment? Great, then all that remains is to figure out how to turn on the gas boiler. Do you think it’s enough to insert the plug into the socket and select the temperature? No matter how it is. Before this, it is necessary to bleed the air and fill the system with water. You will find instructions with the sequence of actions in our article.

First start of the boiler: beginning

The initial startup allows you to assess the condition of the heating system.

Important! In case of problems when switching on independently, the service center may refuse warranty. Perhaps the best solution would be to contact a specialist.

In any case, a specialist must make the connection to the gas pipeline. Installation and wiring of equipment is carried out strictly according to the diagram. It is important to comply with the requirements for the room for wall-mounted and floor-standing boilers, the distance from the wall and the floor. If all installation work has been successfully completed, proceed to the next step.

Filling the system with water

In order for liquid to enter the system, the water valve must be opened. It is located at the bottom of the body. More precisely, you can look in the instruction manual for your model “Ariston”, “Proterm”, “Navien”.

Unscrew the valve gradually; water should not flow in abruptly, otherwise an air lock will occur. As a result, heating problems will begin. Monitor the pressure gauge while filling. As soon as the values reach 2-2.5 atm, close the tap.

Work with water must be carried out in the warm season, otherwise the liquid will form plugs. If the temperature outside is sub-zero, warm the room to 20 degrees.

After installing and filling a double-circuit or single-circuit heating boiler, proceed to remove the remaining air in the pipes.

Bleeding air from the system

Automatically switched on equipment may have an air release function. But it’s more effective to do the work yourself. If you want the room to maintain a stable temperature, then eliminate the possibility of blockages in the pipeline. This is true for old and new models.

Start the process with radiators. Open the Mayevsky taps located on them.

Place the containers first, because water will flow with the air. As soon as the whistling and hissing stops, you can close the taps.

Bleeding begins with the battery, which is located above the rest.

Before starting the boiler, remove air from the pump. Can you do it yourself? It is better to carry out the first bleeding manually, despite the automation. How to proceed:

Remove the case by unscrewing the screws;

Connect the Visman, Kiturami, Aton boiler or the one you have at your disposal to the outlet;
As soon as the device is started, the pump will turn on and you will hear a gurgling sound;
Using a slotted screwdriver, unscrew the pump nut;

As soon as water flows, tighten the nut back. Repeat the procedure until the gurgling stops.

Monitor your pressure gauge readings. If the pressure has dropped, add fluid to the circuit.

An important point is setting up the batteries. Far radiators are turned on at maximum, and near ones at minimum. As soon as a comfortable indicator is reached, proceed to the next stage.

Crimping the circuit

During startup, this step is often ignored by users. But in vain! The procedure allows you to immediately find out how reliable and tight the system is. Judge for yourself: if a leak occurs at the height of the heating season and you are left without heat, the costs could be much higher. All you need is a pressure pump at hand.

Blow out the system with a powerful air stream. The interval between starts is 10 minutes. During this time, keep an eye on the pressure gauge. Has your blood pressure started to drop? This means there is a leak that needs to be found and fixed.

Cleansing by rinsing

To ensure that nothing interferes with water circulation in the future, open all the taps on the radiators. Now supply the liquid under pressure of 4 bar, having previously placed the containers. The stream will clean the pipes of rust and sediment. Then clean the filters from dirt.

How to turn on a gas boiler?

The system is prepared, proceed to start the independent boiler. Is it possible to turn it on without gas? No, you need to follow the sequence.

For mounted units “Bosch”, “Vailant”, “Beretta”, “Ferroli” (Ferroli), Protherm, Celtic and other models:

Plug in the device;
Unscrew the gas valve;
Press the “Start” button (depending on the model there may be a different key. See the instructions);
Using the “+” or “-” buttons on the control panel, set the desired temperature;

The burner with electronic ignition will light up automatically when switching to hot water supply (DHW) or heating. For piezo ignition, hold down the flame control for a few seconds, then press the piezo button.

Important! During the initial start-up, air may have accumulated inside the gas line, so ignition may be blocked. To remove the lock, press the Restart button.

For parapet boilers of the Aton type, switching on is carried out in a similar way. If there is a remote control, then you can set the mode using the remote control.

How to properly turn on the floor-standing units “Buderus” (Buderus), “Baxi” (Baxi), “Lemax”, “AOGV”, “Conord”, “Danko”, “Siberia” and others:

Ventilate the room;
Make sure there is draft in the chimney;
Open the appliance door;

The control and temperature selector must be in the “Off” position;
Open the gas valve;
Set the selector to the piezo ignition position;
Press the selector for 5 seconds and simultaneously press the piezo button. The burner should light up;
Use the same knob to adjust the temperature values.

Is it possible to leave the boiler on while away? If you're leaving home for an extended period of time, simply set your settings to minimum. Low temperatures and frosts will lead to freezing of the entire system and other equipment. Metal pipes can burst under pressure, then you will have to completely change the heating circuit.