Surely every owner has thought about updating the interior of a house or apartment. In particular, this applies to the bathroom. When carrying out major renovations, owners often encounter problems with dismantling old plumbing. Dismantling and installing a toilet is a very difficult task. However, anyone can do this kind of work with minimal experience and tools. Later in the article we will look in detail at how to dismantle an old toilet with your own hands.

Preparation

First we need to prepare the work area. To do this, remove all rugs and shelves from the bathroom. Make sure there are no fragile parts nearby. We will also need working tools, namely:

• pliers;
• hammer;
• chisel;
• hacksaw for metal;
• wrench;
• stationery knife.

Additionally, you will need a basin, rubber gloves, safety glasses and rags.

Before dismantling the toilet with your own hands, you need to turn off the water in the riser. Next, all the liquid from the tank is drained into a basin.

Phased dismantling

First you need to remove the toilet seat. This can be done using a wrench. Then the lid and support are removed from the tank. Next you need to find the elements that secure the tank to the wall. Typically the element is secured with bolts or nuts. They should be unscrewed using a tool.

What to do if the bolts are rusty?

Please note that fasteners may rust. IN in this case For dismantling, use a hacksaw. We cut off the necessary bolts and move on to the next stage.

We continue work

When cutting off the last nut, try not to break the tank - call an assistant to hold part of the toilet. Next you need to disconnect the pipes that are supplied to it. To do this, use an adjustable wrench. Pay attention to the way the toilet is mounted. It is usually installed to the floor with bolts and sealant. Using a sharp blade (you can use a utility knife), we cut the sealant.

Next, unscrew the bolts. If they are also rusty, we use the same method with a hacksaw. Then slightly raise the toilet. You need to move it relative to the main sewer pipe. Next, we proceed to dismantling the bell. To do this, you need to slightly scroll it and shake it in different directions. Often it is immediately disconnected after dismantling the corrugation.

When dismantling the toilet, try not to contaminate the sewer drain pipe. If debris gets in there, it can cause serious blockage in the system.

After this, drain the remaining water from the siphon. To do this, lift the edge of the toilet. Next, install the container and plug the pipe pipe with a rag. If this is not done, the smell of sewage will spread throughout the apartment. This completes the dismantling of the toilet.

Installation

Installation should be done only after finishing work has been completed, that is, on tiles or on a flat, cemented surface. Installation begins by connecting the device to the sewer. For this purpose, a corrugated outlet is used.

It is better to purchase a new element - it is unlikely to work with the old toilet. Next, a rubber seal is put on the toilet outlet pipe. The latter is pre-moistened in water. Then the toilet is installed in the chosen place and the second end of the corrugation is attached to the sewer pipe.

At the base of any modern toilet there are mounting lugs. Through them, using a marker or pencil, marks are made on the floor. Disconnect the corrugation from the sewer outlet and move the toilet to the side. This will free up space for drilling holes in the marked places. During the work we will need a hammer drill. The diameter of the hole must correspond to the plugs that come with the toilet mounting kit. You will also need special drills with pobedit tips. They are suitable for working with concrete and tiles.

Next, the toilet is returned to its original place. It is necessary to align the holes made with the factory ears. Fastening is carried out with bolts or using long screws with a hex head. Pay attention to the tightening torque. It is important not to overdo it so as not to deform the ceramic floor tiles.

The final stage of installation is to seal all joints where the toilet comes into contact with the floor.

If the toilet has no ears

There are also such plumbing fixtures. In this case, installation is carried out using epoxy adhesive or cement mortar. But in order for the connection to be of high quality, it is necessary to ensure maximum cleanliness of the surface. For this floor, all dirt and dust are removed.

We fix the drain tank

So, the main part of the toilet has already been installed. All that remains is to secure the drain tank and connect it to the water supply. To do this, we use two bolts and a rubber gasket. The latter is put on the outlet side of the cistern. Long bolts with washers are installed in special holes. Next, the tank is installed in its place.

It is necessary to align all the holes, namely two mounting holes and one drain hole. The bolts are tightened from below with plastic nuts with so-called wings (metal “turnkey” ones will not work, otherwise the element may be damaged). One hand is enough to ensure a tight connection.

Connection to water supply

Now you need to connect the toilet tank to the water supply system. To do this, use a flexible hose with nuts at both ends. You can see what this element looks like in the photo in the article.

It is important to ensure maximum tightness. For better sealing, you should use FUM tape, but sometimes rubber gaskets are included with the hoses.

At this point, installation and dismantling of the toilet has been successfully completed. After which you can turn on the water supply system. The plumbing will be fully usable after the sealant has completely dried.

Conclusion

So, we found out how to install and dismantle a toilet. As you can see, all the work can be done with your own hands. When dismantling the toilet, try not to break the tank - it is very heavy and flimsy. The help of a second person will not be superfluous. Also, do not move the toilet yourself. The weight of a ceramic product can reach thirty kilograms.

Add site to bookmarks

• Kinds
• Choice
• Installation
• Finishing
• Repair
• Installation
• Device
• Cleaning

How to dismantle an old toilet

Since all plumbing in an apartment or house must always remain in working order, it must be changed periodically. Therefore, in any case, you will have to face the problem of dismantling the toilet before installing a new one. It is possible to do this with your own hands. Removing the toilet is not a pleasant job, but it is done quite quickly and easily. Dismantling a toilet includes the following stages: the preparatory stage, freeing the base of the toilet from the floor, dismantling the toilet from the sewer system and installing a temporary plumbing fixture.

Dismantling of an old toilet must be done with extreme care, without damaging the sewer system, as well as existing repairs.

Preparatory work before removing the toilet

Removing a toilet and attaching a temporary plumbing fixture is not as difficult a task as it might seem. In order to dismantle the toilet before its subsequent replacement, you need to stock up on the following materials and tools:

• crowbar;
• wrenches of different sizes;
• pliers;
• rags needed to get rid of residual water;
• latex gloves;
• disinfectant.

When dismantling the toilet, be sure to wear rubber gloves; this will help you avoid microtraumas and infections. Before starting work plumbing fixture you need to thoroughly wash and treat with a disinfectant, for example, a chlorine solution. It can be rinsed with water with an antiseptic dissolved in it - ordinary chlorine-containing bleach.

After this, the workspace must be cleared of all foreign objects, everything should be removed, even rugs.

Removal of plumbing should begin by shutting off the cold water in the supply pipeline. The remaining water in the tank must be drained and the sewer system rendered inactive. You should not use water yourself, and you should also warn your neighbors above so that they refrain from water procedures for a while. After making sure that the supply valve is shut off securely, you can begin work.

Return to contents

Freeing the toilet base

Work begins by disconnecting the flexible water supply hose. Then you will need to dismantle the flush tank, because removing the toilet together with the tank will be quite problematic. To do this, drain the remaining water, unscrew the fastening nuts located on the back of the structure, and open the lid. The tank, hanging on hinges on the wall, can be removed without opening it.

Next you need to clear the base. If your bathroom has beautifully laid tiles, you will have to knock them out. The toilet is attached to the floor in two or four places at the bottom. The connection can be a nut connection, when the device is mounted into the floor using studs, or using dowels with hexagonal heads. However, in both cases, the fastener will be unscrewed with a wrench of the required size.

When connecting with studs, slightly lift the base and, with light rocking movements, loosen the seal in the sewer outlet pipe. If the socket seal was made using cement mortar, it must be chipped using a chisel before removal. It is best to use a thin chisel, breaking off the cement very carefully, with light blows - the tip of the chisel should be directed across the coating, otherwise the toilet outlet or pipe socket may be damaged. As soon as the coating cracks on one side, the same operation will need to be done on the other side of the outlet. They pick out the fragments and try to get the toilet bowl out of the pipe. If this does not work, you need to continue chipping the cement.

If you are faced with such a complex mounting option as fixing the toilet on a wooden board, then dismantling the plumbing can lead to damage. The bottom will simply have to be beaten off. The fastenings will remain in the floor along with the base, which will be removed in parts after the work is completed.

Old plumbing fixtures are usually thrown away; you shouldn’t feel sorry for them.

To avoid injury during work, carefully follow all safety precautions - use gloves and safety glasses.

Return to contents

Freeing the toilet from the sewer pipe

The toilet is now connected only to the cast iron sewer pipe, and it can be disconnected in several ways. These methods have different degrees of damage caused. Before removing the device, it is recommended to make a plug that looks like a rag gag, about 10 cm in diameter. She will need to plug the hole in the sewer pipe, thereby preventing sewer gases from escaping into the apartment.

The first way is destruction. According to this method, you will need to remove the outlet, take out the toilet and simply clean the pipe of any remaining ceramics and mortar. The outlet can be broken off if the device is no longer attached to the floor; in this case, it is necessary to clean the connection between the outlet and the pipe as much as possible from the cement mortar. The toilet is lifted and pulled up. All that remains is to clean the sewer pipe of any residue, being careful not to damage it. The sewer pipe must be protected from clogging with fragments; it is better to plug the hole with something.

You can choose a less destructive method if you are trying to keep your plumbing intact. The joint between the sewer pipe and the toilet must be cleaned of mortar, sealant and other impurities, removing even the smallest residues. Lift the product and determine how freely it moves in the pipe. Slowly loosening and turning the outlet, it is necessary to pull it out of the socket, while clearing it of the solution. The pipe needs to be cleaned for upcoming installation.

Installing a toilet with your own hands is a rather complicated task and will require certain skills and tools. However, if you do this yourself, then, firstly, you can save on a specialist, and secondly, you will gain invaluable experience - after all, new skills are always useful.

Toilets, due to their diversity, differ in the installation method. The most common type is floor-mounted.

Required Items

Before installing a toilet with your own hands, you need to make sure you have the items you will need for this:

• Hammer;
• Adjustable wrench and wrench;
• Hammer;
• Screwdrivers;
• Sealant;
• Transfer collar for connection to a cast iron socket;
• A container into which water will be drained from the plumbing fixture being dismantled, as well as rags for wiping.

Preparation

Before you change the toilet with your own hands, you will need to carry out preparatory activities. First you need to determine how the new device will be connected to the sewer. There are three cuff options:

• Corrugated - this connection method is the most cost-effective. However, with this method, installation cannot be carried out close to the sewer pipe.

Before connecting the toilet using a corrugated cuff, you should make sure that the room has the necessary space and will comfortably accommodate the equipment.

• Direct is a universal connection method that allows you to do this reliably. If you have any doubts about choosing a sewer connection method, then this option is the best.
• Eccentric - a method of connecting to the sewer, convenient if the centers of the drain and socket are shifted.

Connecting the toilet flush using a cuff

To properly install a toilet with your own hands, it is recommended to remove the old line and install a new one. Its length should be equal to the distance from the water supply pipe connection to the toilet connection, plus 15-20 cm.

Dismantling

Before replacing the toilet, you will need to dismantle the old one. For this you will need:

• Turn off the water supply;
• Disable eyeliner;
• Drain the contents from the barrel;
• Remove the barrel. If the old toilet is not planned to be used anywhere, then this can be done with a hammer, otherwise you will have to act carefully;
• Remove the fastening tools used to install the bowl, remove it, pouring out the remaining water.

If you decide to use brute force and use a hammer or hammer to dismantle the old toilet, you should be careful not to allow various fragments to fall into the drain, which will cause a blockage.

If there is any support made of wood or other material under the old bowl, then it must be removed. The void that remains after this operation must be filled with cement and leveled with a spatula.

http://www.youtube.com/watch?feature=player_embedded&v=Y1XRh22HZKE

Toilet installation

• Before installing the toilet yourself, it is necessary to clean the socket from rust and dirt. Then you need to cover it with sanitary sealant and connect the cuff.

When the toilet is removed, odors come out of the sewer. So that they do not distract from work, the sewer hole must be covered with something, for example, plugged with rags.

• Do-it-yourself toilet installation continues with markings for dowels. To do this, the bowl is placed in the place where it is to be installed, and the holes are marked. Drill holes according to this marking and insert dowels into the holes.

In some models, the holes are drilled at an angle. In this case, to install the toilet in the holes, you need to drill at the same angle.

• When the dowels are inserted, the bowl is placed in its place and connected to the cuff from the sewer socket. Then screws are tightened, onto which plastic washers are put.

It is not correct to immediately tighten the screws too much. First you need to lightly bait it and evaluate whether the installation was done smoothly. If not, then level it by placing plastic pads under it. Only after this can you tighten it.

The bowl is installed according to the markings

• To install the toilet, you need to assemble the barrel yourself if it is delivered disassembled. Here everything should be done according to the instructions supplied by the manufacturer.

All moving parts must not come into contact with each other or the walls of the drain tank.

• The next step is installing the drain tank on the bowl. Fastening is usually done using bolts, which should be tightened evenly. When installation is complete, a lid is placed on the tank and a drain button or lever is installed.

• The final moment of self-installation of the toilet is connecting the water supply.

When the water supply is connected, do not rush to turn on the water. First you need to check all structural components visually for damage. And only if you are sure that everything looks normal, you can open the water, fill the reservoir and try to rinse. If leaks occur, they must be repaired.

Today we will talk about how to properly remove an old toilet before installing a new one.

How to remove a toilet

First of all, you need to determine how you have it installed. If the old toilet is installed on top of the tiles, then there should be no problems with dismantling. Unscrew the fastening bolts, use a knife to cut through the glue or sealant at the junction of the toilet with the floor and undermine it.

It will be worse if the old toilet is installed on a board, and besides, it is walled into the floor. This is how toilets were installed before, when there were no hammer drills.

Let's look at the old toilet mounting diagram.

1. Mounting screws. They rot completely due to time and moisture.
2. Board filled with concrete.
3. Concrete screed on the floor.
4. Nails driven into the board for better adhesion to concrete.

With this method of installing a toilet, you cannot do without a hammer and a hammer drill.

Dismantling the toilet

Now let's determine how the toilet is connected to the sewer. If the connection is made using a corrugated pipe, then you are in luck. With this connection method, it is even possible to save the old toilet.

It is also easy to remove a toilet connected to plastic sewer pipes.
It is most difficult to dismantle a toilet when it is connected to a cast iron sewer.

How to dismantle a toilet

This means that you have decided that your toilet cannot be taken at a swoop. It is deeply immured in the screed, the outlet is covered with cement in a cast iron pipe. In this case, you will have to act harshly.
We put gloves on our hands and glasses on our eyes. GLASSES MANDATORY! Take a hammer, 500 grams and go ahead. No, stand. Don't go ahead. First, take a sponge and soak up all the water from the toilet. Be prepared for an unpleasant smell from the sewer.
Yes, by the way, it is assumed that the drain tank is disconnected and removed. I won’t write now how to remove the tanks. This needs to be dedicated to a separate article. There are too many types of tanks and methods for attaching them.
So, we take a hammer and start hitting the toilet. Our main task is not to damage the sewer. Therefore, first we break the toilet outlet.

Well, then we hit the toilet bowl itself. We break it down, clean it up, take out the trash. The result should be a picture like this.

How to remove a toilet with your own hands

The next step in dismantling the toilet is cleaning the sewer pipe. Take a hammer, chisel or old chisel and carefully clean the inside of the pipe.

Attention! Make sure that the fragments do not fall into the sewer. You can plug the pipe with a rag. A MUST FOR EVERYONE! Tie it with wire or rope to prevent it from falling into the sewer. And then incidents happened.
After using a chisel, it is advisable to clean the inside of the cast iron socket with coarse sandpaper.
We fight the unpleasant smell from the sewer. You can put a plastic bag on the pipe and wrap it around the pipe with electrical tape.

Removing an old toilet

Now we have to seal the floor before installing the new toilet. For this we use cement mortar or self-leveling mixture. I do not recommend using tile adhesive. Firstly, it will take a long time to harden. Secondly, glue is, first and foremost, glue. They stick to it. They don't use concrete.

Now we just have to wait for the solution to harden. And you can install a new toilet.
As practice shows, the main problem when performing such work is the lack of a toilet. The old one is broken, the new toilet has not been installed. The solution takes a long time to cool. How to use the toilet? In principle, you can use a new toilet. While the solution hardens, we construct some kind of podium from several boards. By raising the toilet above the floor in this way and connecting it with a corrugated pipe to the sewer, we obtain a temporary solution to the problem. Uncomfortable? Yes. But, no need to ask your neighbors.

Add site to bookmarks

• Kinds
• Choice
• Installation
• Finishing
• Repair
• Installation
• Device
• Cleaning

How to dismantle a toilet?

When making major renovations in the bathroom, many decide to replacing an old toilet. And this is correct, since with modern and stylish plumbing fixtures, the updated interior of such a room will only benefit. But it is absolutely clear that before installing a purchased toilet, it is necessary to dismantle the old one. And here many people have difficulties, because the need to carry out such work arises extremely rarely, and not everyone has the skills and knowledge in this matter. In order not to turn to professionals for help, you can try to do it all yourself. But first, you must first study the information on how to remove an old toilet. It is presented in step-by-step form below.

If you cannot dismantle the old toilet, you will have to break it. To do this you will need a hammer and a crowbar.

Stage 1: carrying out preparatory work

Before you remove the old toilet, you will need to prepare your work area. You will need to remove shelves and rugs from the bathroom. In addition, you need to take out all those objects and things that will block the space. After all, if you leave them, then dismantling the old plumbing will be inconvenient. In addition, while performing such work, you can accidentally touch fragile objects, which will eventually break.

After that, bring it to workplace the following tools and materials:

• hammer;
• wrench;
• chisel;
• glasses;
• basin;
• hacksaw for metal;
• pliers;
• latex gloves;
• rags (rags).

Return to contents

Stage 2: dismantling old plumbing

First of all, you need to remove the toilet seat from the toilet. This can be done using a wrench of the appropriate size. Next, the lid of the tank is removed, and then its support is disconnected from the plumbing. Then you need to pay attention to the fasteners that secure the water collection container to the wall. You can usually see that the tank is attached with nuts or bolts. They will need to be unscrewed using a suitable tool. But it also happens that this is not possible. As a rule, this can be observed due to the fact that the fasteners have rusted. In this case, you will need to take a hacksaw and cut off the studs between the tank and the wall. But such work must be carried out with special care. It’s great if during their implementation someone will help you hold the tank, otherwise it may fall and break, ultimately damaging the finishing floor covering. Once it is disconnected from the wall, it will need to be disconnected from the water supply pipes.

Now you need to pay attention to how the toilet is fixed to the floor. In most cases, you will see that the plumbing fixture is installed with caulk and bolts.

First you need to unscrew the fasteners. Then take a knife and use it to cut the sealant by inserting a sharp blade and slightly lifting the old toilet. Then you need to loosen the toilet a little, trying to move it relative to the sewer pipe.

Next, you need to dismantle the bell. It will need to be loosened and twisted a little. In some cases, it immediately disconnects after the corrugation has been removed. Therefore, there will be no problems with carrying out such work. Once completed, you will need to drain the remaining water from the siphon. To do this, first lift the front edge of the toilet. Then the prepared container is substituted, and the remaining liquid is poured into it. After doing this, immediately plug the background pipe with a rag so that the sewer smell does not fill your home. If you don’t have it on hand, you can use a plastic bottle.

This will complete the removal of the old toilet. You just need to take it and the tank out of the toilet. After this, it will be possible to install new plumbing; if necessary, during such work it will be possible to immediately replace the corrugation if it is noticed that it has become very worn out.

Return to contents

What difficulties may arise?

The above instructions describe the most easy way removal of old plumbing. However, it is often impossible to use it, because if the corrugation and the tank, as a rule, can be removed without problems, then the toilet itself can not always be detached from the floor quickly and without hassle. After all, plumbing fixtures are usually replaced after 15-25 years of use. As a result, the nuts on which it is fixed, which served faithfully due to high humidity, may not unscrew at all. There are also cases when the toilet is literally cemented into the floor. Here, of course, dismantling it causes a lot of trouble. But with the right approach they can be minimized.

So, if the old plumbing fixture cannot be unscrewed, then its base will need to be destroyed. Here you will need to arm yourself with a hammer, a crowbar and a hacksaw. But first you will need to literally soak all the water from the toilet siphon, because if this is not done, then after dismantling you will have an unpleasant and long cleaning.

It is imperative to wear gloves and safety glasses when breaking down the toilet. Before starting this work, remove the tank and disconnect the corrugation. Next you need to do a few strong blows on the base of the plumbing. After this, you will notice how cracks have appeared in the lower part of the toilet. Hit them a few more times, and then start knocking out the part that turned out to be more stable. Use a chisel and crowbar during this process. With their help, even a secure fixation will be detached. After that, all that remains is to clean the surface on which the new toilet will be installed in the future, and the old plumbing can be safely taken outside and thrown into the trash can.